![]() ![]() Failure to follow recommended installation and servicing procedures, modifications, alteration or improper use will void this warranty. Any product that is abused, altered, incorrectly installed or used in competition is not covered. ![]() This warranty is for the original purchaser and is non-transferable. EOP’s limit of liability under this warranty is to repair or replace the product at EOP’s option.Ĭonsequential costs such as, but not limited to labor fees, loss of use, loss of time or freight charges are not covered. As always we supply the best filtration on the market and the Endura is completely waterproof and submersible.ĭimensions: 39.37 cm long x 10.80 cm wide x 16.51 cm high (includes air filter)Īir Filter can be relocated for ease of fitmentĪll products sold by EOP are warranted to be free from defects in materials and workmanship for a period of one year (unless otherwise noted) from original date or purchase. You can easily run two Endura compressors for the ultimate in air volume with low overall amperage draw. This is a great compressor for filling tires, air bag suspensions, air horns, air tools and air lockers. The Endura is designed with a smaller and leaner mounting footprint to allow easier fitment in a variety of applications.The Endura has a 100% continuous duty rating and a 200 psi max working pressure. ![]() Length 1Ĥĕ0375K82 High-Pressure/Vacuum Polyethylene Tubing 1/4" ID, 3/8" OD, 1/16" Wall Thickness, Black, 25 ft.The ExtremeAire Endura is our newest 12 volt compressor. Length 1ġĕ053K48 Quick-Assembly Brass Compression Tube Fitting, Straight Adapter for 1/4" Tube OD X 1/4 Male Pipe 2Ģĕ053K53 Quick-Assembly Brass Compression Tube Fitting, Straight Adapter for 3/8" Tube OD X 1/4 Male Pipe 2ģĕ0375K81 High-Pressure/Vacuum Polyethylene Tubing. In addition to what I bought on the 1st post.ġĕ053K37 Quick-Assembly Brass Compression Tube Fitting, Straight Adapter for 1/4" Tube OD X 1/8 Female Pipe 1Ģĕ053K48 Quick-Assembly Brass Compression Tube Fitting, Straight Adapter for 1/4" Tube OD X 1/4 Male Pipe 1ģĕ053K31 Quick-Assembly Brass Compression Tube Fitting, Tee for 1/4" Tube OD 1Ĥĕ0785K322 Medium-Pressure Brass Threaded Pipe Fitting, 1/4 Pipe Size, Female X Male X Female Tee 2ĥĕ0785K43 Medium-Pressure Brass Threaded Pipe Fitting, 1/4 Pipe Size, 90 Degree Male X Female Elbow 1Ħė775K12 Quick-Opening Brass Check Valve, 1/4 NPTF Dryseal Female Connections, Buna-N Seal 1ħĔ921K16ĝrain-Handle Brass Stop Cock, Wing-Nut Handle, 1/4" NPT Male, External Seal 1ĨĔ8435K72Ğxtend-Life ASME Pop-Safety Valve with Test Ring, Brass, Medium Flow, 1/4 NPT Male, 145 PSI 1ĩĕ0375K81 High-Pressure/Vacuum Polyethylene Tubing. A line comes up from the tank, where it T's off there I have another line run through the firewall to connect to my gauge/switch. Otherwise it will blow its fuse if you try and start it when its hooked up to something with a lot of pressure. Note to use the harbor freight compressor I needed to add a check valve. We'll see how it does, I can always relocate it. I mounted the compressor in the engine compartment however I am a little worried about heat. If the pressure is low, the 12v passes through the switch and activates the relay. The on/off switch will feed 12v to the pressure switch. I followed the wiring from the diagram in the Viair manual. I had to get a 1/8 to 1/4 NPT adapter for the compressor. ARB CKMTA12 High Performance 12 Volt On-Board Air Compressor with 0830001 Smart Pressure Control Tire Inflation and Deflation System for ARB Air Lockers Locking Differentials 5.0 out of 5 stars 2 853.00 853. 3/8 OD from the air tank to the regulator. 1/4 OD for the pressure gauge and supply from the harbor freight compressor. The air lines are high pressure, hard poly. Carpet is kinda nasty, I must have a leak somewhere because its a little bit damp.Īctually I wouldn't mind having the regulator mounted under the rear bumper if it was weatherproof. If anyone has done this before let me know. I'm going to move that regulator a bit after I pull up the carpet in the back and lay down some bedliner. Still a work in progress with a little wiring and tidying up left to do, but I have the air lines run and everything ready for the Viair gauge/switch. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |